汽车手机架是手机或GPS定位导航必备的车载支架，夹具宽度可自由调节，最小42mm,最大85mm，适合市面上绝大部分款式的手机，也可横屏放置GPS导航！有了手机架能够方便车主使用手机，车载手机支架在近年来也是非常火热的，不过使用车载手机支架也是有注意事项的。

The car phone is a mobile phone or GPS positioning navigation must have the vehicle bracket, the width of the fixture can be adjusted freely, minimum 42mm, maximum 85mm, suitable for most of the market style of mobile phones, but also the horizontal GPS navigation! With mobile phones can be used to facilitate the use of mobile phones, mobile phones in recent years is also very hot, but the use of mobile phones is also a matter of attention.

手机架的用处：

Use of mobile phones:

1、标准配件：主体、链接杆、空调口扣具、底座.吸盘。

1, standard accessories: main body, link rod, fastener, air conditioning export base. Chuck.

2、支架链接，可调试任意弯曲角度；

2, support link, can debug any bending angle;

3、超强吸贴力，吸贴在挡风玻璃下更牢固；

3, strong suction force, the suction is more firmly under the windshield;

4、具有油压、阻尼、双向弹开的效果；

4, with the oil pressure, damping, the effect of the two way projectile;

5、运动平稳、噪音小、夹臂开度大；

5, the movement is steady, the noise is small, the clamping arm is open;

6、配上不同夹座或吸盘可适用于车载及桌上或家用；

6, with different clamping seat or suction cup can be applied to the car and table or home;

首先对于新手肯定是不会安装车载手机支架的，我们第一步要将固定夹臂A向外拉伸，将手机等收纳物品放入；第二如需将屏幕横向放置，请用手指分别捏住固定夹臂A和固定夹臂B，将其向左或向右转动90度；第三请确保手机等收纳的已稳妥地夹放于手机架内；第四将手机等收纳物夹放于手机架上决定安装位置，确认粘贴所需空间及左右旋转所需空间。

First of all, the novice is not installed on the mobile phone, we first step to the fixed clip arm A out, the mobile phone and other items into; second if you need to put the screen horizontal, please use your fingers to hold the fixed clip arm B and the fixed clip arm A, third degrees to the left or right.

其次看看安装后会不会妨碍到您的驾驶；

Second look at the installation will not hinder your driving;

1.请在手机已夹放于车载手机架上的状态时确认左右旋转所需空间。

1 please confirm the space required for the left and right space when the mobile phone has been placed in the vehicle on the vehicle frame.

2.使用角度调节片进行安装时，请将角度调节片折弯并确认角度是否适合于实际安装位置。

2 adjust the angle of the film to install, please adjust the angle adjustment and confirm the angle is suitable for the actual installation position.

3.手机架本体倾斜朝下时不可安装使用。

3 mobile phone frame body is inclined to be installed when the use of the.

4.附属的双面胶粘贴于本体背面；

4 double sided adhesive tape affixed to the back of the body;

5.将粘贴位置的污垢、油脂等用中性洗涤充分擦拭后用水抹净。并用毛巾拭干；

5 will paste the location of dirt, grease, etc. with a neutral detergent to wipe clean after the full use of water. And dry with a towel;

6.将双面胶准确贴于粘贴位置。为确保粘性的充分发挥，请在粘贴后24小时内不要将手机等物品放入手机架。因重复粘贴会使双面胶粘性降低，请勿重复使用。

6 will double adhesive tape on paste position accurately. In order to ensure the full play, please do not put the phone into the phone rack 24 hours after the paste. Because of repeated paste will make double-sided adhesive viscosity reduction, do not repeat the use of.

注意事项：

Note:

粘贴时必须占用23mm-79mm以上范围的平面，不可粘贴于曲面、毛绒布面或者凹凸不平的表面；车载手机支架请勿安装在妨碍安全气囊动作或者妨碍驾驶的地方；使用时，请确认手机架和收纳物品均已稳妥固定好；请勿将手机等物品放置在手机架上后下车离开，高温可能会损坏您的电子产品；如手机等物品的侧面有按键等，收纳时可能会出现不便。

Paste must occupy 23mm-79mm range above the plane, do not paste on the surface, plush cloth or uneven surface; mobile phone holder do not install in interfere with airbag action or interfere with the driver's place; when in use, please make sure that the mobile phone holder and receive goods are safe fixed; do not mobile phones and other items are placed in the mobile frame after left off heat may cause damage to your electronic products, such as mobile phones and other items of the side keys, admission may be inconvenient.